INGDAO HYTANG HAND TRUCK CO.,LTD. ,
http://www.cnwheelbarrow.com</p>Wheel</a></span></p><p></p><p>Pneumatic Wheel, Small Pneumatic Wheels, Semi Pneumatic Wheels</p><p>Q:unset;font-size: unset;font-family: unset;font-weight: unset;text-decoration:underline;">Pneumatic ><span class="keywords_replace"><a href="
http://www.cnwheelbarrow.com/pneumatic-wheel/" style="color outside of the vehicle body so as not to force the cable line when lifting and lowering the bar. <pg effect. When installing two cable lines, care should be taken to leave a 15-20 CM allowance on theattention to the installation. Put on the packing and tighten the Gulen fitting to ensure the sealinng to the illustration. Pay attention to the one-to-one correspondence between the cable lines; pay the large and small Gulen connectors on the vehicle body, and the cable wires are connected accordie cable and the four-core cable on the lifting rod are respectively introduced into the body throughhe pin in the U-shaped bracket is inserted into the positioning hole on the lifting rod. The six-pole lifting rod to the top of the vehicle body and place it into the U-shaped bracket to ensure that ts. Install the junction box cover. <br><br> 6. Install the lighthouse lifting rod Lift the lighthous and connect the cables as shown in the figure. Note the order of connection of the four lamp holder Connect the input cables of the four lamp holders to the junction box at the top of the lifting rodn of the four lamp holders to the horizontal position. The four lamps are fixed on the beam in turn.he bolts fixing the lamp holder on the top beam of the lifting rod; then adjust the mounting positiog rod to prevent the rope on the pulley from falling off. <br><br> 5. Install the lamp cap Unscrew t state and must not be loosened. Install the pin on the upper hole of the front pulley of the liftinont end of the wire rope is facing in the direction of the chuck, and ensure that it is in a clampedottom pulley of the car body and fix the wire rope with the pin. Pay attention to ensure that the frulley at the front position of the lift bar. Then pull the wire rope back to the upper hole of the b the pulley, and then pass the pulley removed from the front part of the lift bar, and install the phole of the pulley position at the bottom of the car body, pull it out from the lower groove part ofhe front end of the lifting rod. Pass the wire rope on the winch of the car body through the square positioning pins on the front end pulley of the vehicle body and the pulley and positioning pin on t with a chain; finally, the support is removed. <br><br> 4. Install the wire rope to remove the two he iron rings at both ends of the bottom of the carriage, and then the hook of the tow bar is hookeditable height, and then insert the fixing pin. The chain inside the carriage is taken out, hung on tdy and bolt it inside the car body. Then lower the front support leg, adjust the support leg to a subracket inside the car body, and then pull out the L-bracket. Insert the tow bar into the vehicle bo body, and then open the side door of the car body. Use a wrench to unscrew the bolts holding the L-n the support feet. <br><br> 3. Install the tow bar and use the support to lift the front of the carht of the rear support feet so that the wheels are off the ground and the weight of the body falls oleg to the appropriate position, and then insert the fixing pin. Shake the rocker to adjust the heigth sides of the supporting leg of the rear part of the tailgate of the car, pull out the supporting rear of the vehicle body with the Allen screw. <br><br> 2. After installation, remove the pin on bo vehicle body. The positioning pin of the U-bracket is on the left side. Secure the U-bracket to the on the rear end of the body. Position the U-bracket in the installation position at the rear of the 1. Install the U-shaped bracket Open the side door of the body and remove the socket head cap screw
